Everything Safety N Training Blog

Everything Safety N Training ESNT is your one stop online home of safety information and training blogs.

Safety Gallery

_DSC5932
Work at Heights Training, What are You Doing to Meet this Requirement?

The Everything Safety N Training place to find unique safety photos.

This weeks feature photo was provided by Charles. It is a new high rise apartment building being built. This photo captures the building on a foggy morning with the clouds below the tower crane. This photo was edited in Picasa.

Send us your best safety photos with your brand as to avoid any copyright issues and we will feature them in our safety gallery for all to see. Please ensure that all photos are original and no copyrights are violated. Once submitted to Everything Safey N Training we will decide each week which photos make the cut.

Please give us some background on your submitted photos. i.e. the subject of the photo, maybe where it was taken or when it was taken.

The best way to avoid any issues is to only submit photos that you have taken and edited.

Everything Safety N Training reserves the right to reject any photos for copyright concerns.

Bench  Grinder Hazards 39
Bench Grinder Hazards

Bench grinder work rest must be properly adjusted to within an 1/8 inch.

1926.303(e)

“Work rests.” On offhand grinding machines, work rests shall be used to support the work. They shall be of rigid construction and designed to be adjustable to compensate for wheel wear. Work rests shall be kept adjusted closely to the wheel with a maximum opening of 1/8 inch (0.3175 cm) to prevent the work from being jammed between the wheel and the rest, which may cause wheel breakage. The work rest shall be securely clamped after each adjustment. The adjustment shall not be made with the wheel in motion.

DSC03405

1926.1053(b)(1) 

When portable ladders are used for access to an upper landing surface, the ladder side rails shall extend at least 3 feet (.9 m) above the upper landing surface to which the ladder is used to gain access.

P1060647

1926.1404(q)(1)

The outriggers or stabilizers must be either fully extended or, if manufacturer procedures permit, deployed as specified in the load chart.

P1000220

Lifelines: Any employee using lifelines must be trained in safe lifeline usage and the hazards of using lifelines.

IMG_0069

1926.1424(a)(2)(ii)

Erect and maintain control lines, warning lines, railings or similar barriers to mark the boundaries of the hazard areas. Exception: When the employer can demonstrate that it is neither feasible to erect such barriers on the ground nor on the equipment, the hazard areas must be clearly marked by a combination of warning signs (such as “Danger–Swing/Crush Zone”) and high visibility markings on the equipment that identify the hazard areas. In addition, the employer must train each employee to understand what these markings signify.

IMG_2607 (Small)

What are you doing to prevent dropped objects? Prevention dropped objects is a must on all construction sites.

IMG_2497

All scaffold erectors must be trained and competent.

 DSC00129

Shielding and eye protection required.

DSCF2429

A great tower crane view for any training presentation.

P1060495

Looking away does not substitute for the use of the correct welding PPE.

Welding shields. Constructed of vulcanized fiber or fiberglass and fitted with a filtered lens, welding shields protect eyes from burns caused by infrared or intense radiant light; they also protect both the eyes and face from flying sparks, metal spatter and slag chips produced during welding, brazing, soldering and cutting operations. OSHA requires filter lenses to have a shade number appropriate to protect against the specific hazards of the work being performed in order to protect against harmful light radiation.

Paint Hazards 37 - Copy (2) (1024x459)

Flammable Liquids Hazards: Where are the flammable cabinets, marked Flammable – Keep Fire Away?

DSC00366

OSHA requires that all unprotected ends of platforms be protected.

Crane Scene 36

All lifting and rigging will inspected before use and protected when not in use.

Cutting Torch Hazards 57

Jubilee clips are not allowed to be used on torch sets.

DSC01558

Welding, cutting and grinding, use the PPE.

Worker Scene 01

Any Employee making any CSE (Confined Space Entry must be Trained.

steel-fixing-02

Steel Erection

tower-cranes-17

Tower Cranes

gas-plant-construction-222

Gas Plant Construction

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

%d bloggers like this: